ethyl 2-(trimethylsilylmethyl)prop-2-enoate

Modify Date: 2024-01-05 11:38:06

ethyl 2-(trimethylsilylmethyl)prop-2-enoate Structure
ethyl 2-(trimethylsilylmethyl)prop-2-enoate structure
Common Name ethyl 2-(trimethylsilylmethyl)prop-2-enoate
CAS Number 74976-84-4 Molecular Weight 186.32400
Density 0.897 g/mL at 25ºC(lit.) Boiling Point 70-72ºC10 mm Hg(lit.)
Molecular Formula C9H18O2Si Melting Point N/A
MSDS Chinese USA Flash Point 140 °F
Symbol GHS07
GHS07
Signal Word Warning

 Names

Name ethyl 2-(trimethylsilylmethyl)prop-2-enoate
Synonym More Synonyms

 Chemical & Physical Properties

Density 0.897 g/mL at 25ºC(lit.)
Boiling Point 70-72ºC10 mm Hg(lit.)
Molecular Formula C9H18O2Si
Molecular Weight 186.32400
Flash Point 140 °F
Exact Mass 186.10800
PSA 26.30000
LogP 2.44390
Index of Refraction n20/D 1.438(lit.)

 MSDS


Section1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE
Product identifiers
Product name: Ethyl 2-(trimethylsilylmethyl)acrylate
CAS-No.: 74976-84-4
Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Laboratory chemicals, Manufacture of substances



Section2. HAZARDS IDENTIFICATION
Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]
Skin irritation (Category 2)
Eye irritation (Category 2)
Specific target organ toxicity - single exposure (Category 3)
Classification according to EU Directives 67/548/EEC or 1999/45/EC
Irritating to eyes, respiratory system and skin.
Label elements
Labelling according Regulation (EC) No 1272/2008 [CLP]
Pictogram
Signal wordWarning
Hazard statement(s)
H315Causes skin irritation.
H319Causes serious eye irritation.
H335May cause respiratory irritation.
Precautionary statement(s)
P261Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
P305 + P351 + P338IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
Supplemental Hazardnone
Statements
According to European Directive 67/548/EEC as amended.
Hazard symbol(s)
R-phrase(s)
R36/37/38Irritating to eyes, respiratory system and skin.
S-phrase(s)
S26In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice.
S36Wear suitable protective clothing.
Other hazards - none

Section3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
Synonyms: 2-(Trimethylsilylmethyl)acrylic acid ethyl ester
Ethyl 2-(trimethylsilylmethyl)propenoate
Formula: C9H18O2Si
Molecular Weight: 186,32 g/mol
ComponentConcentration
Ethyl 2-(trimethylsilylmethyl)acrylate
CAS-No.74976-84-4-

Section4. FIRST AID MEASURES
Description of first aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Consult a physician.
In case of eye contact
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
If swallowed
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with
water. Consult a physician.
Most important symptoms and effects, both acute and delayed
To the best of our knowledge, the chemical, physical, and toxicological properties have not been
thoroughly investigated.
Indication of any immediate medical attention and special treatment needed
no data available

Section5. FIREFIGHTING MEASURES
Extinguishing media
Suitable extinguishing media
For small (incipient) fires, use media such as "alcohol" foam, dry chemical, or carbon dioxide. For large
fires, apply water from as far as possible. Use very large quantities (flooding) of water applied as a mist or
spray; solid streams of water may be ineffective. Cool all affected containers with flooding quantities of
water.
Special hazards arising from the substance or mixture
Carbon oxides, silicon oxides
Advice for firefighters
Wear self contained breathing apparatus for fire fighting if necessary.
Further information
Use water spray to cool unopened containers.

Section6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate ventilation.
Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapours accumulating to
form explosive concentrations. Vapours can accumulate in low areas.
Environmental precautions
Prevent further leakage or spillage if safe to do so. Do not let product enter drains.
Methods and materials for containment and cleaning up
Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and
place in container for disposal according to local regulations (see section 13). Keep in suitable, closed
containers for disposal.
Reference to other sections
For disposal see section 13.

Section7. HANDLING AND STORAGE
Precautions for safe handling
Avoid contact with skin and eyes. Avoid inhalation of vapour or mist.
Keep away from sources of ignition - No smoking.Take measures to prevent the build up of electrostatic
charge.
Conditions for safe storage, including any incompatibilities
Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are
opened must be carefully resealed and kept upright to prevent leakage.
Recommended storage temperature: 2 - 8 °C
Specific end use(s)
no data available

Section8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Components with workplace control parameters
Exposure controls
Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and
at the end of workday.
Personal protective equipment
Eye/face protection
Safety glasses with side-shields conforming to EN166 Use equipment for eye protection tested
and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique
(without touching glove's outer surface) to avoid skin contact with this product. Dispose of
contaminated gloves after use in accordance with applicable laws and good laboratory practices.
Wash and dry hands.
The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and
the standard EN 374 derived from it.
Body Protection
impervious clothing, The type of protective equipment must be selected according to the
concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator
with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup
to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air
respirator. Use respirators and components tested and approved under appropriate government
standards such as NIOSH (US) or CEN (EU).

Section9. PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
a) AppearanceForm: clear, liquid
Colour: light yellow
b) Odourno data available
c) Odour Thresholdno data available
d) pHno data available
e) Melting point/freezingno data available
point
f) Initial boiling point and 70 - 72 °C at 13 hPa - lit.
boiling range
g) Flash point61 °C - closed cup
h) Evaporation rateno data available
i) Flammability (solid, gas) no data available
j) Upper/lowerno data available
flammability or
explosive limits
k) Vapour pressureno data available
l) Vapour densityno data available
m) Relative density0,897 g/cm3 at 25 °C
n) Water solubilityno data available
o) Partition coefficient: n- no data available
octanol/water
p) Auto-ignitionno data available
temperature
q) Decompositionno data available
temperature
r) Viscosityno data available
s) Explosive propertiesno data available
t) Oxidizing propertiesno data available
Other safety information
no data available

Section10. STABILITY AND REACTIVITY
Reactivity
no data available
Chemical stability
no data available
Possibility of hazardous reactions
no data available
Conditions to avoid
Heat, flames and sparks.
Incompatible materials
Strong oxidizing agents
Hazardous decomposition products
Other decomposition products - no data available

Section11. TOXICOLOGICAL INFORMATION
Information on toxicological effects
Acute toxicity
no data available
Skin corrosion/irritation
no data available
Serious eye damage/eye irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
IARC:No component of this product present at levels greater than or equal to 0.1% is identified as
probable, possible or confirmed human carcinogen by IARC.
Reproductive toxicity
no data available
Specific target organ toxicity - single exposure
Inhalation - May cause respiratory irritation.
Specific target organ toxicity - repeated exposure
no data available
Aspiration hazard
no data available
Potential health effects
InhalationMay be harmful if inhaled. Causes respiratory tract irritation.
IngestionMay be harmful if swallowed.
SkinMay be harmful if absorbed through skin. Causes skin irritation.
EyesCauses serious eye irritation.
Signs and Symptoms of Exposure
To the best of our knowledge, the chemical, physical, and toxicological properties have not been
thoroughly investigated.
Additional Information
RTECS: Not available

Section12. ECOLOGICAL INFORMATION
Toxicity
no data available
Persistence and degradability
no data available
Bioaccumulative potential
no data available
Mobility in soil
no data available
Results of PBT and vPvB assessment
no data available
Other adverse effects
no data available

Section13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Product
This combustible material may be burned in a chemical incinerator equipped with an afterburner and
scrubber. Offer surplus and non-recyclable solutions to a licensed disposal company. Contact a licensed
professional waste disposal service to dispose of this material.
Contaminated packaging
Dispose of as unused product.

Section14. TRANSPORT INFORMATION
UN number
ADR/RID: -IMDG: -IATA: -
UN proper shipping name
ADR/RID: Not dangerous goods
IMDG: Not dangerous goods
IATA:Not dangerous goods
Transport hazard class(es)
ADR/RID: -IMDG: -IATA: -
Packaging group
ADR/RID: -IMDG: -IATA: -
Environmental hazards
ADR/RID: noIMDG Marine Pollutant: noIATA: no
Special precautions for user
no data available



SECTION 15 - REGULATORY INFORMATION
N/A


SECTION 16 - ADDITIONAL INFORMATION
N/A

 Safety Information

Symbol GHS07
GHS07
Signal Word Warning
Hazard Statements H315-H319-H335
Precautionary Statements P261-P305 + P351 + P338
Personal Protective Equipment Eyeshields;full-face respirator (US);Gloves;multi-purpose combination respirator cartridge (US);type ABEK (EN14387) respirator filter
Hazard Codes Xi: Irritant;
Risk Phrases 36/37/38
Safety Phrases 26-36
RIDADR UN 1993
Packaging Group III
Hazard Class 3.2
HS Code 2931900090

 Synthetic Route

 Customs

HS Code 2931900090
Summary 2931900090. other organo-inorganic compounds. VAT:17.0%. Tax rebate rate:13.0%. Supervision conditions:AB(certificate of inspection for goods inward,certificate of inspection for goods outward). MFN tariff:6.5%. General tariff:30.0%

 Articles2

More Articles
Synthesis of Carbohydrate Derived a-Methylene-?-lactones by Diasterecseldctive, Low Temperature Reformatsky-Type Reactions. Csuk R, et al.

J. Carbohydr. Chem. 5(3) , 459-467, (1986)

Synthesis of Carbohydrate Derived α-Methylene-γ-lactones by Diasterecseldctive, Low Temperature Reformatsky-Type Reactions Csuk R, et al.

J. Carbohydr. Chem. 5(3) , 459-467, (1986)

 Synonyms

ethyl 2-(trimethylsilylmethyl)acrylate
MFCD00075508
ethyl (2-trimethylsilylmethyl)-prop-2-enoate
(2-Ethoxycarbonylallyl)-trimethylsilane
Ethyl 2-(trimethylsilylmethyl)propenoate
ethyl 2-methylene-3-(trimethylsilyl)propionate
2-(Trimethylsilylmethyl)acrylic acid ethyl ester
ethyl 2-(trimethylsilanylmethyl)acrylate